| Featured Products this Week |
|
|
| 400 W AC-DC Converter for Industrial Power System Applications | |
AC to DC Converter
from Vicor
|
| The PFM4414VB6M24D0CA0 from Vicor is an AC-DC Converter that steps down an AC input voltage of 85 - 264 V to a DC output voltage of 24 V. This converter delivers an output power of up to 400 W and has an efficiency of 91.3%. It offers a robust mechanical design with built-in EMI filtering. This ultra-low-profile converter incorporates AC-DC conversion, integrated filtering, and transient surge protection. It has a versatile two-sided thermal strategy. |
| |
Download Datasheet
Product Details | |
|
|
|
| Off-Line CV/CC ZVS Flyback Load Switch IC for Flyback Design Applications | |
Power Switch IC
from Power Integrations
|
| The INN4176C-H190 from Power Integrations is an Off-Line CV/CC ZVS Flyback Integrated Load Switch IC that has been designed to dramatically improve the efficiency of flyback power converters. This switch requires an input voltage of 85 - 264 V. It delivers an output power of 180 W in adapter mode (typical non-ventilated enclosed adapter) and 200 W in open frame mode. This switch integrates both primary and secondary controllers that are magnetically coupled. |
| |
Download Datasheet
Product Details | |
|
|
|
| 600 V Trench IGBT for Air Conditioner Applications | |
IGBT
from Sanken Electric
|
| The FGM623S from Sanken Electric is a Trench IGBT that is ideal for air conditioner and power conditioner applications. It has a collector-emitter voltage of less than 600 V, a saturated collector-emitter voltage of 1.5 V, and a gate-emitter of ±30 V. This IGBT has a collector current of less than 30 A and a power dissipation of up to 60 W. It decreases gate capacitance with its trench structure, enabling high-speed switching and minimizing switching loss. |
| |
Download Datasheet
Product Details | |
|
|
|
| 650 V Direct Drive D-Mode Power Switch for Power Supply Applications | |
GaN Power Transistor
from VisIC Technologies
|
| The V08TC065S1X11 from VisIC Technologies is a Direct Drive D-Mode Power Switch that has been designed for applications requiring high power and efficiency with low volume and cost. It has a drain-source voltage of 650 V, a gate-source voltage of over -25 V, and a drain-source on-resistance of 8 milli-ohms. This GaN transistor has a continuous drain current of up to 200 A and a pulsed drain current of less than 380 A. |
| |
Download Datasheet
Product Details | |
|
|
|
| Automotive-Qualified Small Signal Bipolar PNP Transistor | |
Bipolar Junction Transistor
from Micro Commercial Components
|
| The MMST3906HE3-TP from Micro Commercial Components is an Automotive-Qualified Small Signal Bipolar PNP Transistor that is ideal for small signal applications. It has an emitter-base voltage of up to -5 V and a collector-emitter and collector-base voltage of less than -40 V. This AEC-Q101-qualified transistor has a collector current of up to -200 mA and a power dissipation of less than 200 mW. It features an epitaxial planar die construction and is halogen-free. |
| |
Download Datasheet
Product Details | |
|
|
|
| 22 µH Wireless Charging Receiving Coil | |
Wireless Charging Coil
from Vishay
|
| The IWAS4832AAEB220JF1 from Vishay is a Wireless Charging Receiving Coil that has been designed to support WPC Qi specifications. It has an inductance of 22 µH and an inductance tolerance of ±5%. This coil has a quality factor of 38 and a dynamic contact resistance (DCR) of 427 milli-ohms. It operates over a temperature range of -40°C to +105°C. This RoHS-compliant receiver coil is available in a through-hole. |
| |
Download Datasheet
Product Details | |
|
|
|
| 3000 F Electric Double Layer Capacitor for Mining Applications | |
Supercapacitor
from Eaton
|
| The XL60-3R0308W-R from Eaton is an Electric Double Layer Capacitor that is ideal for backup power, peak power shaving, pulse power, engine starting, energy capture and re-use (hybrids) for automotive, trucks, mining and construction, equipment, cranes, remote power for sensors, LEDs and switch applications. It has a capacitance of 3000 F and a capacitance tolerance of ±20%. This capacitor has a voltage rating of 3 V. |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by DoD Energy & Power Summit 2024 | | DoD Energy & Power Summit 2024 | | The DoD Energy and Power Summit 2024 is a ‘Town-Hall’ style forum that will bring together leaders from across U.S. military services, DoD, federal government, & industry. This event will explore the modernization and advancement of energy and power technologies and solutions that promote energy security, resiliency, and sustainability and that meet the DoD’s installation and operational energy demands. Click here to learn more. | | | |
|
|
| Power Sourcing Equipment Controller IC for Midspan Applications | |
Power Over Ethernet IC
from Analog Devices
|
| The LTC4274A from Analog Devices is a Power Sourcing Equipment Controller that has been designed for use in IEEE 802.3at Type 1 and Type 2 (high power)-compliant power-over-ethernet (PoE) systems. It requires an input voltage of 3 - 4.3 V and delivers an output power of 90 W. This controller uses low-resistance external MOSFETs and 250 milli-ohms sense resistors to ensure low power dissipation, especially at higher current levels. |
| |
Download Datasheet
Product Details | |
|
|
|
| Charger Protection IC for PDA Applications | |
Battery Management IC
from ROHM Semiconductor
|
| The BD6041GUL from ROHM Semiconductor is a Charger Protection IC that is ideal for mobile phones, MP3 players, digital still cameras, PDAs, IC recorders, electronic dictionaries, handheld games, game controllers, camcorders, and Bluetooth applications. This IC requires an input voltage of 2.2 - 28 V. It offers an over-voltage protection of 28 V and has a power dissipation of 725 mW. This battery management IC (BMIC) has a supply quiescent current of 90 µA. |
| |
Download Datasheet
Product Details | |
|
|
|
| 6.6 kW On-Board Charger for EV Charging Applications | |
On-Board Charger
from Brogen
|
| The 6.6 kW EV from Brogen is an On-Board Charger that is ideal for EV charging applications. It requires an input voltage of 90 - 256 V and an input current of up to 30 A. This charger delivers an output power (DC) of 6.6 kW, an output voltage of less than 450 V, and an output current of up to 90 A. It incorporates a DC-DC converter that provides an output power of 1 kW. This on-board charger features a responsive charging mode with a frequency of 50 Hz. |
| |
Download Datasheet
Product Details | |
|
|
|
| 200 kW Motor/Inverter System for Commercial Vehicles | |
EV Traction Motor
from Dana TM4
|
| The SUMO MD HV2200-3P from Dana TM4 is an Automotive-Qualified Motor/Inverter System that has been designed to interface directly with standard e-axles. It delivers a continuous output power of 145 kW and a peak output power of 200 kW. This motor provides a torque of 955 Nm and has a speed of up to 2700 rpm. It comes with proven permanent magnet technology for optimal efficiency and an outer rotor topology for maximum torque density. |
| |
Download Datasheet
Product Details | |
|
|
|
| 12-Channel Power Management IC for Automotive Applications | |
PMIC
from NXP Semiconductors
|
| The MC33PF8200DBES from NXP Semiconductors is a 12 Channel Power Management IC that is designed for NXP’s high performance i.MX 8 and S32x processor-based applications. It requires an input voltage of 2.7 - 5.5 V. This power management IC (PMIC) integrates seven high-efficiency buck converters, four linear regulators with load switch options, and an RTC supply and coin cell charger to control the processor, memory, and miscellaneous peripherals. |
| |
Download Datasheet
Product Details | |
|
|
|
| Electric Transaxles for Agriculture Applications | |
Electric Axle
from e-comer
|
| The TXI SERIE – WHEEL HUBS VERSION from e-comer are Electric Transaxles that are ideal for construction, logistics, e-mobility, cleaning, and agriculture applications. They deliver a continuous output power of 0.8 kW and a peak output power of up to 3 kW. These transaxles provide a torque of 300 Nm and have a speed of less than 7 rpm. They support DC permanent magnet motors (PMDC) and AC induction motors (AMAC). |
| |
Download Datasheet
Product Details | |
|
|
|
| Automotive-Qualified H-Bridge Motor Driver IC for DC Motor Control Applications | |
Motor Driver IC
from Microchip Technology
|
| The ATA6824C from Microchip Technology is a High-Temperature H-Bridge Motor Driver IC that is ideal for DC motor control applications in high-temperature automotive environments. It requires an input voltage of 4.8 - 5.1 V and provides an output current of 100 mA. This motor driver features PWM (pulse width modulation) and direction-controlled driving of four externally powered NMOS transistors. It includes a programmable dead time to avoid peak currents within the H-Bridge. |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by DoD Energy & Power Summit 2024 | | |
|
|
| Dual-Channel Isolated Gate Driver IC for Motor Control Applications | |
Gate Driver
from Teledyne e2v HiRel Electronics
|
| The TDGD274 from Teledyne e2v HiRel Electronics is a Dual-Channel Isolated Gate Driver IC that is ideal for power supplies, battery management systems, DC-DC converters, inverters, and motor control applications. It requires an input voltage of 2.5 - 5.5 V and an input current of 10 mA. This gate driver features PWM input configuration and provides high dV/dt immunity. It offers separate pull-up/down outputs for slew rate control and has a very low jitter. |
| |
Download Datasheet
Product Details | |
|
|
|
| 10 V LED Lighting Power Controller IC | |
LED Driver IC
from Renesas Electronics
|
| The R2A20135SP from Renesas is an LED Lighting Power Controller IC. It requires an input voltage of up to 24 V and provides an output voltage of 10 V. This IC features a high-accuracy LED current feedback system, thereby enhancing LED performance. It supports non-isolation step-down control, which reduces the need for external parts while maintaining a high power factor and efficiency. This IC supports triac, pulse width modulation (PWM), and DC dimming. |
| |
Download Datasheet
Product Details | |
|
|
|
| 1 kW Pure Sine-Wave DC-AC Inverter for Medical Applications | |
DC to AC Inverter
from AIMS Power
|
| The PWRI100012120S from AIMS Power is a Pure Sine-Wave DC-AC Inverter that converts a DC input voltage of 12 V to an AC output voltage of 120 V. It delivers an output power of 1000 W (peak). This lightweight inverter incorporates advanced technology and offers a compact design to provide reliable power transformation for various applications. It supports better thermal capabilities with cooling motors and delivers high efficiency while ensuring clean, green power. |
| |
Download Datasheet
Product Details | |
|
|
|
| 25 V Voltage Transducer for Shunt Isolator Applications | |
Voltage Transducer
from Ohio Semitronics
|
| The VT7-002E from Ohio Semitronics is a Voltage Transducer that is ideal for accurate measurement and isolation of DC voltage/shunt isolator applications. It requires an input voltage of 0 - 25 V and provides an output current of 4 - 20 mA. This transducer offers precise DC voltage measurement, which ensures accurate current readings. It has undergone a 2500 V (AC) dielectric test that evaluates insulation strength and ensures that the transducer meets safety standards. |
| |
Download Datasheet
Product Details | |
|
|
|
| 6 µF AC Power Film Capacitor for General AC Filtering Applications | |
Power Capacitor
from TDK Corporation
|
| The B33331V7605J080 from TDK Corporation is an AC Power Film Capacitor that is ideal for general AC filtering applications. This capacitor has a capacitance of 6 µF and a capacitance tolerance of ±5%. It has a voltage rating of 650 V and an equivalent series resistance (ESR) of less than 21 milli-ohms. This UL-approved capacitor offers a low dissipation factor and features self-healing technology. |
| |
Download Datasheet
Product Details | |
|
|
|
| 3 W Isolated AC-DC Power Supply for Energy Applications | |
AC to DC Converter
from Recom Power
|
| The RAC03-3.3SK/SMT-R from RECOM is an Isolated AC-DC Power Supply that steps down an AC input voltage of 85 - 265 V to a DC output voltage of 3.3 V. It delivers an output power of 3 W and has an efficiency of 69%. This power supply offers an optimized design that is tailored for JEDEC-reflow solder processes. Its footprint measuring 1 inch2 facilitates automated production to ensure a shock and vibration-resistant PCB assembly. |
| |
Download Datasheet
Product Details | |
|
