| Featured Products this Week |
|
|
| Fluxgate DC Current Transducer for Precision Current Sensing | |
Current Transducer
from Danisense
|
| The DL2000ID-CB100 from Danisense is a high-precision DC current transducer (DCCT) measuring up to 3000 A currents. It continuously measures 3000 A currents with a linearity error of less than 1 ppm. This current transducer requires an input current of less than 3000 A while providing current output through the D-sub-9 connector. It is based on the ultra-stable Danisense closed-loop flux gate technology that offers very low offset and ultra-low drift. |
| |
Download Datasheet
Product Details | |
|
|
|
| 650 V GaN Power Transistor | |
GaN Power Transistor
from Nexperia
|
| The GAN039-650NBB from Nexperia is an Automotive Qualified GaN Power Transistor. This transistor has a drain-source breakdown voltage of 650 V, a gate threshold voltage of up to 4.6 V, and a drain-source on-resistance of 33-86 milli-ohms. It has a continuous drain current of 58.5 A. This GaN transistor is a normally-off device that combines Nexperia’s latest high-voltage GaN HEMT H2 technology and low-voltage silicon MOSFET technologies. |
| |
Download Datasheet
Product Details | |
|
|
|
| 355-375 W N-type Monocrystalline Solar Panels | |
Solar Panels
from Jinko Solar
|
| The Tiger N-Type 60TR Series from Jinko Solar are N-type Monocrystalline Solar Panels. These solar panels integrate 120 monocrystalline half-cut MBB cells with tiling ribbon technology. They deliver a module power of 355-375 W (STC) and 265-280 W (NOCT) and a maximum power voltage of 34.04-34.63 V (STC) and 31.74-32.29 V (NOCT). They have an open circuit voltage of 41.01-41.60 V and an open circuit current of 10.43-10.83 A in STC. |
| |
Download Datasheet
Product Details | |
|
|
|
| 300 mA High Voltage Linear Regulators | |
LDO Voltage Regulator
from onsemi
|
| The NCP737 Series from onsemi are High Voltage Linear Regulators. They require an input voltage of 3-65 V. These low-dropout (LDO) voltage regulators provide a fixed output voltage of 3.3 V and an adjustable output voltage of 1.2-20 V and have a low current consumption of up to 15 µA. They have a dropout voltage of over 500 mV and deliver an output current of over 300 mA. They can withstand continuous DC or transient input voltages up to 65 V. |
| |
Download Datasheet
Product Details | |
|
|
|
| 600 V Half-Bridge Gate Driver | |
Gate Driver
from STMicroelectronics
|
| The STDRIVEG612 from STMicroelectronics is a Half-Bridge Gate Driver that is ideal for AC/DC and DC/DC conversion, synchronous rectification, resonant converters, PFC, adapters, and battery charger applications. It requires an input voltage of 10.3-18 V. This gate driver IC has been designed to withstand a voltage of 600 V on the high-voltage rails on the high side. It can also handle high current and supports a propagation delay of 50 ns. |
| |
Download Datasheet
Product Details | |
|
|
|
| Low Noise Single-Channel CMOS Operational Amplifier | |
Power Operational Amplifier
from ROHM Semiconductor
|
| The BD7281G-LBTR from ROHM Semiconductor is a Low Noise High Speed Single Channel CMOS Operational Amplifier. It requires a single supply voltage of 2.5-5.5 V or a dual supply voltage of ±1.25 V to ±2.75 V. This high-speed op-amp features an input offset voltage of up to 2 mV and an input bias current of 0.5 pA. It provides an output voltage of up to 50 mV. It is available in a surface-mount package that measures 2.9 x 2.8 x 1.25 mm. |
| |
Download Datasheet
Product Details | |
|
|
| Sponsored by Micross | | Class H+ DC-DC Converters for LEO Satellites & NewSpace | | The new AFLS Series (120W, 5-28V) is rad-tolerant to 50kRad (Si) TID & 60MeV·cm²/mg SEE, meeting MIL-PRF-38534 Class H requirements, and includes additional tests such as PIND and radiography. Built upon the widely used AFL series’ decades of heritage, the AFLS series provides a cost-effective, solution for LEO & NewSpace missions, launch vehicles, and more. Click here to learn more. | | | |
|
|
| Low Voltage AOT Synchronous Buck Regulator | |
DC to DC Converter
from Kinetic Technologies
|
| The KTB8316EEAA-CJ-TA from Kinetic Technologies is a Low-Voltage AOT (adaptive-on-time) Synchronous Buck Regulator with a switching frequency of 1.2 MHz. It requires an input voltage of 2.5-5.5 V and supports an adjustable output voltage of 0.9-3.3 V. This DC-DC converter delivers an output current of up to 2.5 A and maintains a high output-voltage accuracy of ±0.75%. It offers peak efficiency up to about 90%. |
| |
Download Datasheet
Product Details | |
|
|
|
| 24 V Push-Pull Power Plug-in Connector | |
Power Connector
from Weidmuller
|
| The IE-PS-VAPM-5P-2.5 from Weidmuller is a Push-Pull Power Plug-in Connector. It has a rated voltage of 24 V and a rated current of 16 A. This power connector is designed for more than 100 plugging cycles. It is compliant with the PROFINET specification and IEC 61076-3-126 standard. This IP65/67-rated power connector. This RoHS/REACH-compliant connector is available in a push-pull plug-in package that measures 85.4 x 36.2 x 26.8 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
| 100 V ePower Stage IC | |
PMIC
from Efficient Power Conversion
|
| The EPC23109 from Efficient Power Conversion is an ePower Stage IC. It requires an input voltage of up to 100 V and has a nominal bias supply voltage of 5 V. This PMIC operates at a PWM frequency of 3 MHz. It uses EPC’s proprietary GaN IC technology and integrates an input logic interface, high-side level shifting, synchronous bootstrap charging, and gate drivers along with eGaN output FETs into one monolithic integrated circuit. |
| |
Download Datasheet
Product Details | |
|
|
|
| 1500 W AC-DC Power Modules | |
AC to DC Converter
from TDK Corporation
|
| The PFE1500FB Series from TDK Corporation are AC-DC Power Modules that convert an AC input voltage of 85–305 V to a DC output voltage of 48 V. They deliver an output power of up to 1500 W and have an efficiency of 92%. These converters have high power density and operate from -40 to 100°C. They support PMBus communications for control, programmable droop for load sharing, and adjustable protections. |
| |
Download Datasheet
Product Details | |
|
|
|
| Single-Cell Linear Charger IC for Li ion Batteries | |
Battery Management IC
from Torex Semiconductor
|
| The XC6804B4E14R-G from Torex Semiconductor is a Single-cell Linear Charger IC for Li-ion Batteries for linear charging of single-cell Li-ion batteries and Li-polymer batteries. It requires an input voltage of 4.5-6.0 V. This battery management IC (BMIC) has a CV charging voltage of 4.02-4.23 V, a CC charging current of up to 800 mA. It is available in a surface-mount package with high heat dissipation that measures 40 x 40 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
| DC-DC Converter for Electric Vehicles | |
DC to DC Converter
from Inmotion Technologies
|
| The DCC40M24 from Inmotion Technologies is a DC-DC Converter that steps down an input voltage of 250–500 V to a nominal output voltage of 14.1 V or 28.3 V. It delivers an output power of over 3.75 kW and achieves efficiency levels of up to 97%. This converter provides a maximum output current of 135 A and supports a boost current of up to 175 A. This DC-DC converter is available as a module that measures 438 x 216 x 85 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
|
|
| 54 W High Power Resistor | |
Power Resistor
from EBG Resistors
|
| The MTX 969.54 from EBG Resistors is a Precision High-Voltage and High-Power Resistor. It has a resistance of 2 ohm to 10 GΩ and a resistance tolerance of ±0.1 to ±10%. This resistor has a power rating of up to 54 W. It has a temperature coefficient of up to 200 ppm/°C and can operate over a temperature range from -55°C to +225°C. It has a dielectric strength of more than 1000 V and has an operating voltage of 48 kV DC. |
| |
Download Datasheet
Product Details | |
|
|
|
| 1200 V Automotive-Grade SiC Schottky Diode | |
Power Diode
from Micro Commercial Components
|
| The SICU10120XG4JQ-TP from Micro Commercial Components is an Automotive-Grade Silicon Carbide Schottky Diode. It has a repetitive peak reverse voltage of up to 1200 V and a reverse leakage current of up to 20 µA. This AEC-Q101-qualified power diode has a forward voltage of over 1.55 V and a continuous forward current up to 34 A. It is available in a surface-mount package that measures 10.40 x 6.70 x 2.40 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
| AEC-Q100 Grade 0 Qualified Silicon Motor Driver IC | |
Motor Driver IC
from Toshiba
|
| The TB9M030FG from Toshiba is a Bi-CMOS Linear Integrated Circuit Silicon Monolithic Motor Driver IC that is designed for automotive (electric pumps and fans), three-phase brushless motor control and drive applications. It requires a supply voltage of 6-27 V and a clock frequency of up to 40 MHz. This motor driver integrates a microcontroller unit (MCU) and a gate driver IC for automotive brushless DC (BLDC) motor applications. |
| |
Download Datasheet
Product Details | |
|
|
|
| 12 V Military Grade DC-DC Converter | |
DC to DC Converter
from Gaia Converter
|
| The MGDS-500 from Gaia Converter is a Military Grade DC-DC Converter that converts an input voltage of 9-36 V to an output voltage of 12 V. It delivers an output power of up to 500 W and has an efficiency of 91%. This DC-DC converter is capable of withstanding galvanic isolation voltage levels of up to 1500 V. This Mil-STD-704 standard converter is available in chassis-mount packages that measure 61 x 64 x 12.9 mm. |
| |
Download Datasheet
Product Details | |
|
|
|
| 3.5 A Single-Cell Battery Charger IC | |
Battery Management IC
from Analog Devices
|
| The MAX77785 from Analog Devices is a high-efficiency Single-Cell Battery Charger IC for USB Type-C power delivery. This battery management IC requires an input voltage of 4.7-18.2 V. It delivers up to 3.5 A charge current using an integrated synchronous buck converter with up to 90% efficiency. This battery charger IC supports reverse boost (OTG) operation with programmable output voltage up to 10.8 V. |
| |
Download Datasheet
Product Details | |
|
