| Featured Products this Week |
|
|
| 100 V Half-Bridge GaN Driver for Data Centre Power Supplies | |
Gate Driver
from Analog Devices
|
| The LT8418ACBZ-R7 from Analog Devices is a Half-Bridge GaN Driver that is ideal for half-bridge, full-bridge, push-pull converters, data center power supplies, motor drivers, class-D audio amplifiers, and consumer, industrial, and automotive applications. It requires an input voltage of 3.85–5.5 V. This gate driver features a smart integrated bootstrap switch that simplifies circuit design, while the split-gate driver allows for fine-tuning of turn-on and turn-off strengths. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 100 V Enhancement-Mode GaN Power Transistor | |
GaN Power Transistor
from Efficient Power Conversion
|
| The EPC2361 from Efficient Power Conversion is an Enhancement Mode GaN Power Transistor that is ideal for synchronous rectification, DC-DC conversion, motor drives, and solar MPPT applications. It has a drain-to-source voltage of over 100 V, a gate threshold voltage of up to 2.5 V, and a drain-source on-resistance of less than 1 milli-ohm. The GaN transistor has a continuous drain current of up to 101 A and a pulsed drain current of less than 519 A. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 80 V Symmetric Dual N-Channel MOSFET | |
MOSFET
from Vishay
|
| The SiZF4800LDT-T1-GE3 from Vishay is a Symmetric Dual N-Channel MOSFET. It has a drain-source breakdown voltage of 80 V, a gate threshold voltage of 2 V, and a drain-source on-resistance of less than 19 milli-ohms. This MOSFET has a continuous drain current of up to 36 A and a power dissipation of less than 56.8 W. It features high-side and low-side MOSFETs to form an optimized combination for a 50% duty cycle. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 24 V IP20-Rated Surge Suppression Device for Monitoring/Protection | |
Surge Suppression IC
from Phoenix Contact
|
| The 2906831 from Phoenix Contact is a Fine Surge Suppression Device that has been designed for continuous monitoring of protective devices and medium current rectification (MCR) applications. It has a voltage rating of 24 V(DC) and a current rating of up to 10 A. This suppressor features an integrated status indicator for a signal wire with a grounded reference potential and benefits from optional remote signaling. It is available in an IP20-rated DIN rail-mount package. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 23.3 A Inrush Current Limiter for Machine-Building Applications | |
Inrush Current Limiter
from Camtec Power Supplies
|
| The ESB101.33 from Camtec Power Supplies is an Inrush Current Limiter that is ideal for high loads in LED applications, complex automation systems, and machine-building applications. It is self-powered and does not require an external power supply. This RoHS-compliant current limiter requires an input voltage (AC) of 184 - 264 V and has a current rating of 23.3 A (RMS) and 33 A (peak). It can offer effective and interference-free operation with capacitive loads. |
| |
Download Datasheet |
Product Details | |
|
|
|
| IP67-Rated Buck DC-DC Converter for Telecom Applications | |
DC to DC Converter
from Analytic Systems
|
| The VTC1050-48 from Analytic Systems is a Buck DC-DC Converter that converts an input voltage of 130 - 390 V to an output voltage of 48 V. It provides an output current of up to 110 A. This converter offers power factor-corrected input stages and increased efficiency over the previous auto-switching technology, ejecting input voltage dead spots and allowing the voltage converter to run continuously. It incorporates heavy input and output filtering to reduce electromagnetic interference. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 3.6 A Electronic Fuse for SSD Array Applications | |
eFuse IC
from STMicroelectronics
|
| The STEF05LPUR from STMicroelectronics is an Electronic Fuse that has been optimized for monitoring output current and the input voltage on 5 V DC power lines. It requires an input voltage of 4.5 - 8 V and delivers an output current of 3.6 A. It can detect and respond to over-current and over-voltage conditions when connected in series to the main power rail and limits the output current to a safe value defined by the user. |
| |
Download Datasheet |
Product Details | |
|
|
|
| -40 V High-Speed SiC Junction Field Effect Transistor | |
Junction Field Effect Transistor (JFET)
from NTE Electronics
|
| The NTE466 from NTE Electronics is a High-Speed SiC Junction Field Effect Transistor that is ideal for industrial and commercial applications. It has a drain-source breakdown voltage of -40 V and a drain-source on-resistance of 25 milli-ohms. This field-effect transistor (FET) has a continuous drain current of up to 50 mA and a power dissipation of less than 0.36 W. This RoHS-compliant JFET exhibits an extremely fast switching speed that is not affected by variations in temperature. It is available in a through-hole package that measures 18.03 x 5.84 mm. |
| |
Download Datasheet |
Product Details | |
|
|
|
| High Current Shielded Power Inductor | |
Power Inductor
from Allied Components International
|
| The PCSE15Q8-R24M-RC from Allied Components International is a Shielded Power Inductor. This power inductor has an inductance of 0.24 µH and an inductance tolerance of ±20%. It has a saturation current rating of 9.5 A and a DC resistance of less than 18 milli-ohms. This RoHS-compliant inductor exhibits molded construction that ensures durability. It offers high current capacity, making it capable of handling demanding electrical loads with ease. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 150 W High Power Metal Clad Braking Resistors | |
Power Resistor
from Riedon Resistors
|
| The BR150 Series from Riedon Resistors are High Power Metal Clad Braking Resistors. They have a resistance of 0.1 - 1000 ohms and resistance tolerances of ±1%, ±5%, and ±10% These resistors have a power rating of 150 W. They are designed using wirewound technology in a compact package and provide an option for non-inductive winding design. These RoHS-compliant resistors are available in chassis-mount packages that measure 8.27 x 1.61 mm. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 11 V Electric Double Layer Capacitor for Microprocessor Applications | |
Supercapacitor
from Ohmite Manufacturing
|
| The LJ055474A from Ohmite Manufacturing is an Electric Double Layer Capacitor that is ideal for CMOS, RAMs/microprocessors, timers for ICs, relays, solenoids, actuators, disc drives, coin metering devices, utility meters, and vehicle tracking applications. It has a capacitance of 0.47 F and a capacitance tolerance of -20%/+80%. This capacitor has a voltage rating (DC) of 5 V/11 V and an equivalent series resistance (ESR) of less than 6.5 ohms. |
| |
Download Datasheet |
Product Details | |
|
|
|
| Li-ion Battery Pack Fuel Gauge IC for Energy Storage Applications | |
Battery Management IC
from Monolithic Power Systems
|
| The MPF42795 from Monolithic Power Systems is a Battery Pack Fuel Gauge IC that has been designed to provide accurate and robust internal state estimates of batteries ranging from 2 to 10 stacked Lithium cells. It requires an input voltage of 3 - 3.6 V. This IC must be interfaced with battery management system (BMS) analog front-end (AFE) that provides individual cell voltage, pack current, and temperature estimates and M0 system MCU unit. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 650 V N-Channel Silicon MOSFET | |
MOSFET
from Toshiba
|
| The TK042N65Z5 from Toshiba is an N-Channel Silicon MOSFET that is ideal for switching voltage regulator applications. It has a drain-source breakdown voltage of over 650 V, a gate threshold voltage of 4.5 V, and a drain-source on-resistance of 35 milli-ohms. This MOSFET has a continuous drain current of up to 55 A and a pulsed drain current of less than 220 A. It has a power dissipation of 360 W. This Si MOSFET has a fast reverse recovery time. |
| |
Download Datasheet |
Product Details | |
|
|
|
| Synchronous Step-Down Power Management IC for GPU Applications | |
PMIC
from Kinetic Technologies
|
| The KTB8372CEUFA-5C-TA from Kinetic Technologies is a Synchronous Step-down Power Management IC that is ideal for CPU, GPU, DSP, HDD, tablets, notebooks, mobile Internet devices, IoT, DSC, drones, gaming consoles, and TV set-box applications. It requires an input voltage of 4.7 -18 V. This PMIC features integrated high- and low-side FET transistors, advanced adaptive on-time control, and fast transient response for optimal performance. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 2000 W Global Platform Rectifiers for LAN/MAN/WAN Applications | |
AC to DC Converter
from OmniOn Power
|
| The BP040AC48ATEZ from OmniOn Power are Global Platform Rectifiers that step down an AC input voltage of 90 - 264 V to a DC output voltage of 44 - 58 V. They deliver an output power of over 2000 W and have an efficiency of 90%. These rectifiers provide significantly high power density and efficiency improvements in a compact form-factor. They offer a high-density front-to-back airflow design that provides minimal space utilization. |
| |
Download Datasheet |
Product Details | |
|
|
| Sponsored by POWER ELECTRONICS INTERNATIONAL 2024 | | POWER ELECTRONICS INTERNATIONAL 2024 | | Power Electronics International's mission is to bring together, inform, and inspire the power electronics community. Attendees will have numerous opportunities to network with other key industry players and interact face-to-face with manufacturers of process equipment, materials, and metrology technologies in the exhibition hall at Power Electronics International. Click here to learn more. | | | |
|
|
| High Side Load Switch for Consumer Electronics Applications | |
Power Switch IC
from Torex Semiconductor
|
| The XC8101AA01MR-G from Torex Semiconductor is a High Side Load Switch that has been designed for smartphones/mobile phones, digital still cameras/camcorders, and portable game consoles applications. It requires an input voltage of 1.8 - 6 V and provides an output current of 200 mA. This power switch integrates a P-channel MOSFET and is suited for power distribution switching operations. It has an ENABLE pin to provide ON/OFF control . |
| |
Download Datasheet |
Product Details | |
|
|
|
| AEC-Q200 Qualified Magnetically-Shielded Power Inductor | |
Power Inductor
from CODACA Electronic
|
| The VSAD0660-3R3M from CODACA Electronic is an Automotive Qualified Power Inductor that is ideal for Hi-Fi amplifiers, home theater systems, multimedia speakers, musical instrument amplifiers, and car audio applications. This inductor has an inductance of 3.3 µH and an inductance tolerance of ± 20 %. It has a current rating of 7.8 A and a dynamic contact resistance (DCR) of 17.9 milli-ohm. This AEC-Q200-qualified inductor is magnetically shielded. |
| |
Download Datasheet |
Product Details | |
|
|
|
| Radiation-Hardened Half-Bridge GaN Power Stage IC | |
PMIC
from EPC Space
|
| The EPC7011L7SH from EPC Space is a Radiation-Hardened, Half-Bridge GaN Power Stage IC that is ideal for single and multi-phase motor drivers (Reaction wheels, momentum wheels, and robotic actuators), half-bridge/POL power supplies, and satellite electrical power systems applications. It requires an input voltage of 50 V and an input current of 5 A. This GaN power stage consists of gate drivers, level shifter, synchronous bootstrap charger. |
| |
Download Datasheet |
Product Details | |
|
|
|
| 500 W AC-DC Converter for Medical Applications | |
AC to DC Converter
from Bel Fuse
|
| The MEPG500-1012 from Bel Fuse is an AC-DC Converter designed for applications that require low power loss and simple thermal management. It steps down an AC input voltage of 90 - 264 V to a DC output voltage of 12 V while delivering an output power of 500 W at peak efficiency of 94%. This converter is designed with the new efficient GaN power technology while providing a high-power density of 20.83 W/inch3 at an operating temperature of - 40°C to +70°C. |
| |
Download Datasheet |
Product Details | |
|
|
|
| High-Speed Power Operational Amplifier | |
Power Operational Amplifier
from Apex Microtechnology
|
| The PA78DK from Apex Microtechnology is a High-Speed Power Operational Amplifier that is ideal for piezoelectric positioning and actuation, deformable mirror actuators, chemical and biological stimulators, and electrostatic deflection applications. It requires an input offset voltage of 8 mV, an input offset current of 12 pA, and an input bias current of 8.5 pA. This op-amp provides an output current of over 150 mA. |
| |
Download Datasheet |
Product Details | |
|
